E
ECTEK MegaBoard™
The Modular Solution · Interactive Hub
CANADIAN OFFSITE MANUFACTURING

Escape the Drywall Cycle-Time Trap.

One structural Magnesium Oxide (MgO) panel, bound with premium MOC Phase 5 crystalline cement, replaces multi-layer gypsum and wet gypcrete floor pours. Buy back 46 hours of curing time per module, for free.

Download West Coast Comparative Engineering Analysis (PDF)

Full June 2026 technical briefing: lateral shear comparisons, WUI fire assembly listings (UL H509, L567, iSpan), factory cycle-time ROI modeling, and standard fastener warranties.

46 hrs
Curing bypassed
3,575 PLF
Shear capacity
STC 57
Acoustic rating
Wall Assembly Consolidation
Legacy Drywall
5/8" Type X Gypsum
Resilient Channel
Staggered Stud Cavity
5/8" Type X Gypsum
Shear Plywood
5/8" Type X Gypsum
ECTEK MegaBoard
5/8" MgO/MOC ECTEK
Standard 6" cold-rolled
5/8" MgO/MOC ECTEK
Single structural layer. No channels. No staggers.
Buyer Persona Switcher

See it through your lens

Scale throughput from 2.0 → 3.5 volumetric modules per day.

  • Macro ROI: compressed schedules, lower total inventory cost
  • Zero shipping-crack callbacks on road-going modular boxes
  • Capacity recovery: 46 hours of curing → 2 hours mechanical fit
  • Predictable factory cadence drives forecastable revenue
Live Calculator

ROI & Capacity Recovery

Wholesaler CAD material rates. Real tiered savings. Time recovery valued at zero - already included free.

25,000
1,000250,000

Value pivot: Single structural layer replaces double-layer Type X plus shear ply. ASTM E136 non-combustible, 3,575 PLF wall shear (IAPMO ER-710).

Standard Drywall / Gypcrete
$105,500
@ $4.22/SF baseline
ECTEK MegaBoard Setup
$72,500
@ $2.90/SF · 5/8" (16mm) Shear Grade
Direct material delta
−$33,000
≈ $1.32/SF
Bypasses 46 Hours of Curing Time Instantly!
Factory capacity recovery - already priced in.
Verified Performance

Technical Specifications

Third-party listed. Quarterly audited. Internal dossier: $-Mag Board ECTEK_3.

IAPMO UES ER-710
3,575 PLF
Wall nominal shear capacity
IAPMO UES ER-808
2,458 PLF
Blocked diaphragm shear capacity
ASTM E136
100% Non-Combustible
Core combustibility test
ASTM E84
Class A · 0/0
Flame Spread / Smoke Developed
Acoustic Rating
STC 57
On slim 6" cold-rolled profile
ASTM G21 / G3273
Score 0 / 0
Mold + termite immunity
Logical Advocacy Engine

The Bound-Crystal Defense

ECTEK MegaBoard is a Magnesium Oxide (MgO) panel utilizing a premium Magnesium Oxychloride (MOC) cement binder, compliant with CSI Section 09 28 15 (Magnesium Oxide Backing Panels). Here is why a properly engineered MOC board does not behave like the cheap imports the drywall lobby loves to cite.

Uncertified Raw Imports

Cheap, uncertified MOC boards (Danish and Australian failures, 2010 to 2015) use low-purity MgO and an unbalanced molar ratio. The reaction never completes, leaving free deliquescent chloride salts inside the matrix.

Incomplete reaction → free MgCl₂ + Mg(OH)₂ + H₂O

Above 84% RH those free salts pull moisture from the air and "weep" or "sweat" acidic brine, corroding galvanized fasteners from the inside out. This is the failure pattern the drywall lobby weaponizes against the entire category.

ECTEK MegaBoard, Phase 5 Bound

Calcined MgO of extreme purity (at or above 85%) is reacted with magnesium chloride in a precise stoichiometric molar ratio. During a controlled factory heat and humidity curing cycle, 100% of the chloride ions are fully reacted and irreversibly locked into a stable, insoluble Phase 5 crystalline mineral structure:

5 Mg(OH)₂ · MgCl₂ · 8 H₂O (Phase 5)
  • Zero free, dissolvable deliquescent salts to weep.
  • Cannot sweat acidic brine, stable up to 100% RH (uncertified boards fail above 84%).
  • Acts as a permanent, fastener-protecting barrier.
  • Standard corrosion-resistant screws (ceramic-coated, epoxy-coated, GRABBERGUARD) are fully warrantied. Marine stainless is not required.
  • Quarterly third-party QC: UL and QAI audited.
June 2026 Technical Briefing

West Coast Comparative Engineering Analysis

Access the full June 2026 technical briefing detailing lateral shear comparisons, WUI fire assembly listings (including UL H509, L567, and iSpan designs), factory cycle-time ROI modeling, and standard fastener warranties.

Download PDF
Engineering Library

Technical Document Matrix

Engineering Review

Submit Project Documents for Evaluation

Upload your architectural drawings, structural specs, assembly schedules, or wall sections. Our team returns an ECTEK suitability recommendation with substitution callouts within 1 business day.

Auto-attached:Area 25,000 SF·Tier 4 - Multi-Hour Fire / Shear Boundary·Material delta $33,000
Drop files here or click to browse
Drawings · Specs · Schedules · BIM exports

By submitting, you authorize The Modular Solution to reply to your request and to send related ECTEK MegaBoard™ product information, engineering data, and follow-up communications. We do not sell or share your information. Unsubscribe at any time.

Test the panel that ends the cycle-time trap.

Physical samples, full engineering data, and factory audits available to qualified Canadian modular manufacturers.